Double Glazing Door Lock Repairs

Have you noticed that your uPVC window or door mechanism become faulty? Maybe the handles on your uPVC windows or doors aren't aligned properly or are difficult to use.

You will lose energy when your double-glazed doors do not work properly. This also increases the risk of burglary. Owen the Locksmith will be able to fix your door RepairMyWindowsAndDoors lock at reasonable costs.

Snapped Key

When a key snaps off within a lock, it could be incredibly annoying. It could also be a security risk because it could expose you to an intruder if the door does not lock. There are a few easy fixes you can make to repair the issue and make your door functional again.

Be calm. If you panic and begin doing a lot of fumbling around you may end up pushing the damaged piece of the key deeper into the lock, making the situation much worse.

Spray WD-40 or another penetrating lubricant, into the lock. This will assist the broken piece emerge more easily. You can also use a screwdriver to break off any pieces that are stuck. If you're fortunate enough to have a small piece of the key hanging out and you want to remove it, use a paperclip or some other metal object that is thin to grab it and then pull it out. Both methods work, but you must be careful not to push the broken key further into the keyway.

Some paperclips have grooved edges that could be used as a hook extractor and some Jigsaw blades also work for this use. If you don't have any of these handy, you can make use of needle-nose pliers that bend to create a hook. Additionally, you can use a pair tweezers to grab and remove the remaining pieces of broken keys.

If you are unable to get the broken piece of the key out, you can try using a lock de-icer. It is available in most hardware stores and is used to freeze any moisture present in the lock.

If none of these strategies appear to be working, it might be time to call a locksmith. Fitlocks experts can quickly solve problems with uPVC door locks and mechanisms such as snapped keys and broken handles. They can also reconfigure the double glazing door mechanisms so that they are easier to operate. You can schedule an appointment online for a double-glazing repair or contact us to discuss your needs.

Broken Cylinder

A broken cylinder is a serious security threat. A professional locksmith can easily repair the cylinder. To fix the cylinder, locksmiths must tap it. They can do this using an hammer or another tool, but the best method is to employ a long match or a piece of wire. Then, put the match's tip or wire near the keyway. After this, the locksmith will strike the lock to crack it open. This is better than using a hammer that could damage the lock.

The most frequent cause for cylinder head cracks is overheating. This can occur when the block and cylinder head are made from different metals such as cast-iron and aluminum. Different metals can be heated and cool at different rates. This could cause localized hotspots to expand more quickly than the rest.

Corrosion is another possible reason for cylinder fractures. If the cylinder head and the block of the cylinder are not properly maintained, this can cause corrosion or rust that could cause them to expand at a a higher rate than they ought to. Over time, this can also cause cracks.

If your uPVC window or door lock is stiff and requires a lot more pressure to turn it could be due to a variety of reasons. A defective locking mechanism, misalignment, or the wear of the handle are typical causes of this issue.

Fortunately it is a simple and cost-effective fix for the majority of double glazing owners. A professional locksmith will usually be able to resolve this issue within a matter of hours of arriving at your property. They can replace the locking mechanisms, or change the window handles and change the gearboxes, based on your specific needs. A skilled locksmith will always be able to advise you on the most cost-effective solutions for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which provide an additional layer of protection from burglars. It is a small cost to get the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

It's not surprising that window handle locks may break. They have complex mechanisms which deteriorate over time. If yours is damaged it's difficult to identify the cause of the issue. Make sure that you repair it correctly.

The issue could be related to the locking mechanism inside or the latch, fixing your broken handle can improve your uPVC double glazing door's security and allow you stop draughts. Incorrectly repairing or replacing your handle can be expensive and can harm the door's frame as well as lock, so it's worth taking some time to do it right.

With the window replacement open, loosen the screw that secures the handle using a screwdriver. The screw should be on the inside of the backplate. It is typically concealed by a screw cap to enhance the appearance. Be sure not to lose any of the internal components within the handle, for example the levers or plates on the opposite side of the spindle. Ideally, keep these in the same place so you can replace them again in the event of a need.

Then, with an additional screwdriver loosen the screw that connects the handle with the spindle at the back. Once the screw is loose, take the handle off and take the broken spindle out. Replace it with a new one, making sure it's the same length as the previous one (you can typically find these on the internet or at hardware stores) and then securely screw it into the right place. Be careful not to overtighten because this could cause damage to the handle or the window frame.

Close the handle and try it. Hopefully, it will work smoothly and you'll be able open your window once more.

Make sure to check that your uPVC window is shut correctly while you're working with the handle. If they don't, you could experience damp and draughts in your home as in addition to compromising your home's energy efficiency. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure they close properly.

Broken Spindle

It is more common for the spindle to break than the handle. This is especially common in uPVC tilt and turn windows. These types of windows require a handle that is a lock mechanism that is located in the window frame. The handle is attached a central rod which activates mushroom-shaped locking cams that secure into the frame of the window keep. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle has been damaged This can be a frustrating problem.

Fortunately, there are options to rectify this issue. A skilled locksmith can quickly and efficiently solve the issue. They will be able to remove the window handle using a tool that removes the wheel portion of the mechanism, where the spindle goes. This can be done without damage to the handle or the window frame.

After removing the wheel the technician can inspect the spindle and identify the reason for its break. This involves breaking down the spindle into its constituent parts and meticulously noting their general condition as well as any particular areas of wear or damage. The process is done in a clean environment by skilled technicians.

The next step is to clean the damaged spindle. This helps eliminate any debris or dirt that might be obstructing its normal function. After this the spindle is cleaned, it can be repaired or replaced. If it is replaced, the technician can take an identical dowel size to the one used in the first and drill mating holes into both pieces of the spindle. This ensures that the new spindle has precisely matched to the handle.

If the spindle that is damaged is beyond repair, RepairMyWindowsAndDoors it may be required to replace it completely. Home centers sell generic replacements. However, if the design of your window is unique then you will need to find a woodworker or cabinet maker who can make the exact component for you. Once the new spindle is installed, it can be positioned to the handle by lining up the screw holes on the handle with the frames existing screws. Once the new handle is seated you will be ready to operate your uPVC window.