Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like timber and aluminum.

Regularly cleaning and lubricating upvc window repairs windows and doors is crucial. This will prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is essential to take the time to make sure that you're doing all you can to keep your windows in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need source some plastic spacers that will assist the new pane to fit perfectly into the window frame.

If you plan to attempt to remove the window panes yourself, it is essential to wear appropriate safety gear such as gloves that are thick and eye protection. It is also a good idea to lay down a dropcloth before you begin working on the glass, so that any fragments of glass fall onto the fabric rather than on the floor where they can be trampled on and cause further damage.

It's a good idea to cover the gap with tape after the glass is removed. This will stop drafts and water from entering your home until a professional comes out to fix the window. This will also act as a barrier, deterring any intruders from getting access to your home. If the gap is particularly large, you might want to consider using the security door with an integrated window as it offers the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. As time passes, they may develop a number of problems such as sliding. A sagging uPVC window can cause issues with light, draughts and even security. It's crucial to act as soon as you discover that your uPVC windows are falling down.

To repair a window that is sagging, you can try to reposition the hinges. You'll first need to open the windows to reach the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and test it for fitting. If you are happy with the fit of the window, tighten the screws to keep them in the right position.

If you are unable to reposition the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity over time, leading them to loosen. If this happens, it's essential to replace the seal as fast as possible to ensure your uPVC windows are watertight and secure from draughts.

uPVC handles may also loosen up. The majority of the time, this is caused by screws that have come loose over time. However, it can occur because the handle mechanism has been worn out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, you'll need to close the window and perform a test fitting. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle, and then turn the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains, it's crucial to take action. Windows that leak water do not only lead to the destruction of your home's structure but also hamper your efforts to regulate the temperature within your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on the severity of the problem is, the old caulking may have to be removed. When it is time to uPVC repair, it is important to be careful not to over-caulk. This will only make your window more difficult to clean and reduce its energy efficiency.

Make sure that the drainage holes do not have debris inside them and ensure that the sill pan has been properly angled to drain away from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leak originates from the glass of your double-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open in a breeze, it may be the hinges that are at the fault. They can be repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical component hinges will wear out over time. It's very simple to change a Window Replacement Near Me hinge however it is simpler if you have someone to help you to hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the correct direction. Check for the arrows on each hinge to determine which way the window should be opened.

The issue could be caused by opening the window improperly or by a poor installation at the factory. Sending us photos via our website will often resolve the problem. We are more than happy to provide advice.

Regular lubrication of the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is an ideal method to accomplish this. We suggest using the lubricant that doesn't contain solvents, window replacement near me like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also prevent corrosion and reduce the possibility of sticking. The ideal time to perform this every year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by different things. First, the hinges due to wear and tear could become misaligned. This can cause gaps to develop where the sash meets the frame. These can be easily fixed by giving them a good cleaning, but when they're beyond repair, window replacement near me it may be necessary to have them aligned or replaced. The second is the interlock, which is located on the hinge of the window, can also become misaligned, again it is possible to just give them a thorough clean, however in certain cases, it may be necessary to have them replaced.

The next common cause of draughts is the window seals. These are prone to wear or damaged over time, and let air escape through these gaps. Replacing these with high-quality weatherstripping will help to prevent draughts. Replace the upvc windows with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the possibility of draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler that can be placed over your window sill. They will keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security in your home with a little regular maintenance and repairs. It is crucial to recognise that windows last for a certain period of time and there may come the point when it's more efficient to replace them than repair them. If you are having issues with your upvc windows, it's recommended to seek help from a professional as soon as possible.